Western Telematic MT5634 Uživatelská příručka

NPS SeriesNetwork Power SwitchModels NPS-115 & NPS-230(Firmware Version 2.04 and Higher)User's Guide5 Sterling · Irvine · California 92618(94

4. Start-Up / Configuration4.1. System Mode and User ModeIn order to restrict access to sensitive command functions, the NPS features two separateoper

4.2. Communicating with the NPSIn order to configure the NPS or invoke command functions, the user must first connect to theNPS and access command mod

9NPS Series - Network Power Switches, User's Guide Start-Up / ConfigurationNetwork Power Switch v2.04 Site: WESTERN TELEMATIC, INC.Commands:Displ

4.3. NPS Command/Menu ConventionsWhen invoking NPS commands and selecting items from configuration menus, note thefollowing:·All NPS commands can be i

5. Baud Rate: The baud rate for the Modem Port and Console Port. To select the baudrate, type 5 press [Enter], and follow the instructions in the subm

4.5. Plug ParametersThe Plug Parameters menus are used to assign names and select parameters for each individualswitched outlet. There is a separate P

4.6. Network ParametersIn order to communicate with the NPS via network, the IP Address, Subnet Mask and GatewayAddress must first be defined via the

4.6.1. Implementing IP SecurityThe NPS can be configured to restrict unauthorized IP addresses from Telneting to the unit.This allows the user to gran

Example 1: Deny access to all hosts except 192.1.1.5:Security Mask #1: 255.255.255.255 Mask #1 Action: DenySecurity Mask #2: 192.1.1.5 Mask #2 Action:

5. OperationYour PC or Control Device must send ASCII characters at the same data rate as the NPS. Theunit accepts 8 bits no parity, or 7 bits even or

Table of Contents1. Introduction...12. Unit Description...22.1. Fr

5.2. Displaying Plug StatusThe Status Screens display the On/Off state and currently selected parameters for the switchedplugs. To display the Status

When the System Mode is active, the /S command will produce the screen shown in Figure 9,which lists status and parameters for all eight plugs, along

5.3.1. Applying Commands to Several PlugsBoot/On/Off commands can be applied to one plug, several plugs, a range of plugs or all plugsas described bel

5.5. Other Commands5.5.1. Login as Different UserThe /R command is used to re-login using a different password. When invoked, the NPS willdisplay the

21

6. Saving and Restoring ConfigurationParametersAfter the NPS has been properly configured, parameters can be downloaded and saved as anASCII text file

A. Interface DescriptionsA.1. Console Port InterfaceA.2.Modem Port InterfaceApx-1Figure A.1: Console Port InterfaceFigure A.2: Modem Port Interface

B. SpecificationsPower Input/Output: Model NPS-115 (115 VAC)AC Inputs: Dual Bus Circuits, 15 Amps eachVoltage: 100 - 140 VAC, 50/60 HzConnectors: IEC-

C. Customer ServiceCustomer Service hours are from 8:00 AM to 5:00 PM, PST/PDT, Monday through Friday.When calling, please be prepared to give the nam

IndexAAC Inputs...5Access to Command Mode...8, 16BBack Panel...3Baud RateDefault...4Operati

AppendicesA. Interface Descriptions...Apx-1A.1. Console Port Interface...Apx-1A.2. Mo

OOff Command...18-19On Command...18-19ON Indicator...2Operating Tips...20Operation...

1. IntroductionNetwork equipment sometimes "locks-up", requiring a service call just to flip the power switchto perform a simple reboot. The

2. Unit Description2.1. Front PanelAs shown in Figure 1, the NPS front panel includes a series of LED indicators which functionas follows:ÀON: Lights

2.2. Back PanelÀBus B (Plugs5-8): Includes the following components:A) Power Inlet with Cable Clamp: Supplies power for plugs 5 through 8.B) Circuit B

3. Installation3.1. Option SwitchesThe Option Switches select default settings for the Baud Rate, Command Echo, Boot Delay andDisconnect Timeout. Defa

3.3. Connecting an External ModemWhen connecting directly to an external modem, use a standard AT to Modem cable. Makecertain the modem is initialized

3.7.1. Default Parameters OptionThis method allows default parameters to be set without effecting the On/Off status of theNPS's eight switched pl